Cart 0

Effusion Fragrance Lamp Instructions

Effusion Fragrance Lamp Instructions

Step 1 - Open

  • Always place your La-Tee-Da! Effusion Lamp on a flat, protected and stable surface. We suggest a plate, glass, marble or stoneware surface.
  • DO NOT PLACE DIRECTLY ON WOOD OR FINISHED SURFACE.  
  • Put the Vented Crown and Solid Metal Cap beside your Effusion lamp to avoid misplacement.

Step 2 - Fill

  • Use La-Tee-Da! Effusion Fragrances ONLY. Our fragrances are formulated for use exclusively with La-Tee-Da! stone burners.
  • Use the funnel to pour the Effusion Fragrance into the Lamp. Fill the lamp ½ to 2/3 full.
  • DO NOT OVERFILL – (Your Effusion Lamp will not function properly)
  • Wipe lamp, carefully, to clean any fragrance spills.

Step 3 - Insert Wick

  • While holding the Effusion Lamp, insert the Wick Assembly (Burner). It should fit into the collar and be fully seated.
  • Replace the solid metal cap.
  • Wait 20 to 30 minutes before lighting. This will allow the Effusion fragrance to saturate the wick & burner. (The Effusion burner stone will appear darkened or wet when saturated.)

Step 4 - Light

  • Take off the solid metal cap.
  • Light the Effusion burner using a match or lighter.
  • Let flame burn for 2-3 minutes. (Flame will be 5-6” in height, then settle to 1-2”.) When the flame reduces the burner has reached the proper temperature. Take a short meditation moment. DO NOT leave the flame unattended.
  • Blow out the flame. Your La-Tee-Da! Effusion Lamp is now working.
  • Once the flame has been blown out, replace the vented crown over the burner. This will protect the burner from being touched.

Step 5 - Use

  • Leave the Effusion burner open (on) for as long as you require fragrance to be released. It typically takes 30 to 45 minutes to fragrance an average size home.
  • Do not allow the fragrance fuel to run completely out – this will damage the Effusion stone burner over time. The wick assembly will need to be replaced, every 6 - 12 months depending on usage.
  • You can purchase additional wick & stone burners through us at One Of A Kind.
  • If you feel the fragrance is TOO strong… Mix La-Tee-Da! Effusion Fragrance “Dilute” to your Effusion fragrance. Adding this will not change the fragrance integrity but “tone it down.”  

Step 6 - Extinguish

  • Remove Vented Crown. (Caution: Will be hot! You may want to use a glove or oven mitt.
  • Replace Solid Metal Cap to Extinguish the Burner. (It will remain hot for about 10 minutes.)
  • Do Not Refill Effusion Fragrance Until Stone Burner is completely cool.
  • If not using your Effusion Lamp for an extended time frame (3-4 weeks or more) – (Please) remove the Effusion Wick Assembly and any remaining fragrance. Allow all parts to dry completely before storage.  

Step 7 - Change Fragrance or Just Adding...

  • Place the Vented Crown and Solid Metal Cap beside your Effusion lamp.
  • Remove the Effusion Wick Assembly (& Burner) – Place on protected surface. Use a paper towel to remove excess fragrance.
  • Use Funnel to pour your La-Tee-Da! Effusion Fragrances back into the original Bottle. (If you’re planning a fragrance change.)
  • Using the funnel supplied, pour in your New or Favorite Effusion Fragrance until the lamp is ½ to 2/3 full.
  • DO NOT OVERFILL – (Your Effusion Lamp will not function properly)
  • Wipe lamp, carefully, to clean any fragrance spills.
  • You will need to soak your wick again for 20 - 30 minutes, if you have let the wick and burner dry out.